You are here

SAPTIRILMIŞ BORU DEMETİNDE ISI TRANSFERİ VE AKIŞ YAPILARININ BELİRLENMESİİÇİN TEORİK ÇALIŞMA

THEORETICAL STUDY FOR DETERMINATION OF THE HEAT TRANSFER AND FLOW CHARACTERISTICS IN THE STAGGERED TUBE BUNDLE

Journal Name:

Publication Year:

Abstract (2. Language): 
In the present paper numerical analysis of heat transfer and laminar flow structures are studied for staggered tube bundle in crossflow. This study consists of two parts. At the first part isoterms and streamlines are shown for both only single tube heated and all tubes heated cases. At the second part effect of Reynolds number is examined. The stream functionvorticity formulation is used to solve the laminar, steady state Navier-Stokes equations and energy equation by applying Gauss-Seidel over-relaxation technique. Transverse and longitudinal tube spacing is fixed as 1.75x1.5 and results are found for Re=325 and 650.
Abstract (Original Language): 
Sunulan bu çalışmada saptırılmış bir boru demetindeki ısı transferi ve laminer akış yapılarının nümerik incelemesi yapılmıştır. Çalışma iki bölümden oluşmaktadır. Birinci bölümde saptırılmış boru demetindeki borulardan yalnız bir borunun ve boruların hepsinin ısıtılması durumunda eş sıcaklık eğrileri ve akım çizgileri gösterilmiştir. İkinci kısımda ise Reynolds sayısının etkileri araştırılmıştır. Nümerik analiz yöntemi olarak akım fonksiyonuvorticity metodu kullanılarak ve Gauss-Seidel over relakzasyon yöntemi ile Naiver-Stokes ve Enerji denklemleri laminer, kararlı ve sıkıştırılamaz akım için çözülmüştür. Enine ve boyuna boru eksen mesafesi 1.75×1.5 olarak sabitlenip, Re=325 ve 650 için sonuçlar bulunmuştur.
59-68

REFERENCES

References: 

Baughn J.W., Elderkin M.J., Mckillop A.A. (1986): “Heat Transfer from a Single Cylinder,
Cylinders in Tandem and Cylinders in the Entrance Region of a Tube Bank with a
Uniform Heat Flux”, Trans. ASME, J. Heat Transfer, 108, pp 386-391.
Buyruk E. (1996): “An Investigation Into the Effects of Fouling on the Heat Transfer in
Tubular Heat Exchangers”, PhD Thesis, The University of Liverpool.
Buyruk E., Johnson M.W., Owen I. (1998): “Numerical and Experimental Study of Flow and
Heat Transfer Around a Tube in Cross-flow at Low Reynolds Number”, Int. J. Heat &
Fluid Flow, 19, pp 223-232.
Buyruk E., Owen I., Johnson M.W. (2000): “Laminar Flow and Heat Transfer in a Staggered
Tube Bank”, Turkish Journal of Eng. And Environmental Science dergisine gönderildi.
Chen C.K., Wong K.L., Cleaver J.W. (1986): “Finite Element Solutions of Laminar Flow, and
Heat Transfer of Air in a Staggered and an In-line Tube Bank”, Int. J. Heat & Fluid Flow,
7, 4, pp 291-300.
Jain P.C., Goel B.S. (1976): “A Numerical Study of Unsteady Laminar Forced Convection
from a Circular Cylinder”, Trans. ASME, J. Heat Transfer, pp. 303-307.
Johnson M.W. (1990): “Computation of Flow in a Vortex - Shedding Flow-meter”, Flow
Meas. Instrument., 1, pp 201-208.
Murray D.B., Fitzpatrick J.A. (1988): “Local Heat Transfer Coefficients for a Tube Array
Using a Micro-Foil Heat Flow Sensor”, Proc. 2nd U.K. Nat. Conf. on Heat Transfer, 2, pp
1635-1649.
Paolino M.A., Kinney R.B., Cerutti E.A. (1986): “Numerical Analysis of the Unsteady Flow
and Heat Transfer to a Cylinder in Cross-Flow”, Trans. ASME, J. Heat Transfer, 108, pp.
742-748.
Thom A. (1933): “The Flow Past Circular Cylinders at Low Speeds”, Proc. Roy. Soc., A141,
pp. 651-669.
Thompson J.F., Thomes F.C., Mastin C.W. (1974): “Automatic Numerical Generation of
Body Fitted Curvilinear Co-ordinate System for Field Containing Any Number of
Arbitrary Two Dimensional Bodies”, J. Of Computational Physics, 15, pp 299-319.
Zdrovistch F., Fletcher A.C., Behnio M. (1995): “Numerical Laminar and Turbulent Fluid
Flow and Heat Transfer Predictions in Tube Banks”, Int. J. Num. Meth. Heat and Fluid
Flow, 5, pp. 717-733.
Zukauskas A. (1972): “Heat Transfer from tubes in Cross-flow”, Advances in Heat Transfer,
8, pp 93-160.

Thank you for copying data from http://www.arastirmax.com