You are here

BAZALT DOLGULU POLİMER KOMPOZİTLERİN AŞINMA DAVRANIŞLARI

WEAR PROPERTIES OF BASALT FILLED POLYMER COMPOSITES

Journal Name:

Publication Year:

Keywords (Original Language):

Abstract (2. Language): 
In this study, pin-on-disc wear tests of basalt filled, one of the volcanic rocks as a filler material, (10-70wt.%) LDPE polymer matrix composites were performed depending on various sliding speeds at 20 N loads under dry sliding conditions. Wear tests were carried out with configuration of a polymer pin on a rotating AISI 4140 steel disk in the atmospheric conditions under the loads of 20N and at the sliding speeds of 0.5 m/s and 1.5 m/s. The results showed that increase in basalt content of the basalt filled LDPE composites resulted in a decrease of the friction coefficient and wear rate. While the friction coefficient of LDPE composites was changing between 0.11 and 0.51 and basalt content of the polymer composites, and wear rates of the basalt filled LDPE composites ranged from 7.18x10-4 mm3/m to 2.60x10-2 mm3/m, depending on sliding speeds and basalt quantity.
Abstract (Original Language): 
Bu çalışmada, volkanik kayaçlardan bazaltın takviye malzemesi olarak düşük yoğunluklu polietilen (DYPE) matrikse, %10-70 arasındaki değişen oranlarında ilave edilmesiyle elde edilen partikül dolgulu polimer matriksli kompozitlerin değişik sürtünme hızları ve sabit yük altında pin on disk aşınma davranışları incelenmiştir. Aşınma testleri, atmosferik ortamda, 20 N yük altında AISI 4140 çelik diskin 0.5 m/s ve 1.5 m/s dönme hızlarında gerçekleştirilmiştir. Aşınma hızı ve sürtünme katsayısının, bazalt takviyesi ile azaldığı görülmüştür. Bazalt takviyeli DYPE malzemenin kayma hızına ve bazalt miktarına bağlı olarak, sürtünme katsayısı 0.11 ve 0.51, aşınma oranı 7.18x10-4-2.60x10-2mm3/m’ arasında değişmektedir.

REFERENCES

References: 

[1]. Rehbein, P., Wallaschek, J., “Friction and
wear behavior of polymer/steel and alumina/alumina
under high-frequency fretting conditions”, Wear
216, 97-105, 1998.
[2]. Rajesh, J.J., Bijwe, J., Tewari, U.S.,
“Abrasive wear performance of various
polyamides”, Wear 252, 769–776, 2002.
[3]. Gao, J., Mao, S., Liu, J., Feng, D.,
“Tribochemical effects of some polymers/stainless
steel”, Wear 212, 238-243, 1997.
[4]. Bahadur S., Zhang L., Anderegg, J.W.,
“The effect of zinc and copper oxides and other zinc
compounds as fillers on the tribological behavior of
thermosetting polyester”, Wear 203-204, 464-473,
1997.
[5]. Yu, L., Bahadur, S., Xue, Q., “An
investigation of the friction and wear behaviors of
ceramic particle filled polyphenylene sulfide
composites”, Wear 214, 54-63, 1998.
[6]. Suh, N.P., Mosleh, M., Arinez, J.,
“Tribology of polyethylene homocomposites”, Wear
214, 231-236, 1998.
[7]. Aoike, T., Yokoyama, D., Uehara, H.,
Yamanobe, T., Komoto, T., “Tribology of ultra-high
molecular weight polyethylene disks molded at
different temperatures”, Wear 262, 742–748, 2007.
[8]. Guermazi, N., Elleuch, K., Ayedi, H.F.,
Fridrici, V., Kapsa, P.H., “Tribological behaviour of
pipe coating in dry sliding contact with steel”,
Materials and Design, doi:
10.1016/j.matdes.2008.12.003, 2009.
[9]. Shipway, P.H., Hutchings, I.M.,
“Measurement of coating durability by solid particle
erosion”, Surf. Coat. Technol. 71, 1–8, 1995.
[10]. Iwai, Y., Honda, T., Yamada, H.,
Matsubara, T., Larsson, M., Hogmark, S.,
“Evaluation of wear resistance of thin hard coatings
by a new solid particle impact test”, Wear 251, 861–
867, 2001.
[11]. Wood, R.J.K., Puget, Y., Trethewey, K.R.,
Stokes, K., “The performance of marine coatings
and pipe materials under fluid-borne sand erosion”,
Wear 219, 46–59, 1998.
[12]. Iwai, Y., Numbu, K., “Slurry wear
properties of pump lining materials”, Wear 210,
211–219, 1997.
[13]. Hojo, H., Tsuda, K., Yabu, T., “Erosion
Damage of Polymeric Material By Slurry”, Wear
112, 17–28, 1986.
[14]. Stack, M.M., Pungwiwat, N., “Slurry
erosion of metallics, polymers, and ceramics:
particle size effects”, Mater. Sci. Technol. 15, 337–
344, 1999.
[15]. Walley, S.M., Field, J.E., “The Erosion and
Deformation of Polyethylene By Solid-Particle
Impact”, Philosophical Transactions of The Royal
Society of London Series A-Mathematical Physical
and Engineering Sciences 321, .277–303, 1987.
[16]. Knuuttila, J., Ahmaniemi, S., Mantyla, T.,
“Wet abrasion and slurry erosion resistance of
thermally sprayed oxide coatings”, Wear 232, 207–
212, 1999.
[17]. Oblozinsky, P., Ugai, K., Katagiri, M.,
Saitoh, K., Ishii, T., Masuda, T., Kuwabara K., “A
design method for slurry trench wall stability in
sandy ground based on the elasto-plastic FEM”
Computers and Geotechnics 28, 2145-2159, 2001.
[18]. Mertiny, P., “Urethane-lined polymer
composite pipe is designed to resist slurry
hydrotransport abrasion and corrosion”, Materials
Performance 47, 16-18, 2008.
[19]. Yabuki, A., Sugita, K., Matsumura, M.,
Hirashima, M., Tsunaga, M., “The anti-slurry
erosion properties of polyethylene for sewerage pipe
use”, Wear 240, 52–58, 2000.
[20]. Beall, G.H., Rittler, H.L., “Basalt glassceramics”,
Am. Ceram. Soc. Bull. 55, 579–582,
1976.
[21]. Yilmaz, S., Ozkan, O.T., Gunay, V.,
“Crystallization kinetics of basalt glass”, Ceramic
International 22, 477–481, 1996.
[22]. Znidarsic, V., Kolar, D., “The
crystallization of diabase glass”, J. Mater. Sci. 26,
2490–2494, 1991.
[23]. Karamanov, A., Arrizza, L., Ergul, S.,
“Sintered material from alkaline basaltic tuffs”,
Journal of the European Ceramic Society 29, 4, 595-
601, 2009.
[24]. Myshkin, N.K., Petrokovets, M.I., Kovalev,
A.V., “Tribology of polymers: Adhesion, friction,
wear, and mass-transfer”, Tribology International
38, 11-12, 910-921, 2005.
[25]. Rosato, D.V., Schott, N.R., Rosato, M.G.,
“Plastics Engineering, Manufacturing and Data
Handbook”, Plastics Institute of America, Springer,
2006.
[26]. Yang, J.M., Chen, H.S., Hsu, Y.G., Lin,
F.H., Chang, Y.H., “Organic-inorganic hybrid solgel
materials: 2 Application for dental composites”,
Die Angewandte Makromolekulare Chemie 251, 61-
72, 1997.
[27]. Vina, J., Garcia, M.A., Castrillo, M.A.,
Vina I. and Arguelles, A., “Wear behavior of a glass
fiber-reinforced PEI composite”, Journal of
Thermoplastic Composite Materials 21, 279-286,
2008.

Thank you for copying data from http://www.arastirmax.com