Buradasınız

Anasayfa » Content

HOMOJEN DOLGULU SIKIŞTIRMA İLE ATEŞLEMELİ BİR BENZİN MOTORU İÇİN KAM TASARIMI VE İMALATI

CAM DESIGN AND MANUFACTURING FOR A HOMOGENEOUS CHARGE COMPRESSION IGNITION GASOLINE ENGINE

Journal Name:

  • Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi

Publication Year:

  • 2014

Key Words:

Keywords (Original Language):

Author NameUniversity of AuthorFaculty of Author
Abstract (2. Language): 
In this study, cams were designed and manufactured for a homogenous charge compression ignition (HCCI) gasoline engine. Low lift cams were designed accordance with HCCI combustion characteristics for 38 mm base circular diameter, 124° dwell angle, 3.5, 5.5 and 7.5 mm valve lifts. Generic geometric models of cam profiles were obtained using circular arc curves. Obtained models were fitted with fourier series and circular arc curve was derived from the corresponding equations. Speed, acceleration and jerk effects of the follower were investigated for designed cam profiles. Obtained results were compared with cams obtained by 5th degree classical spline method. It has been shown that feature a single point of contact of cam into the follower has been lost and acceleration and jerk values of the follower increased so much as long as valve lift increase in the cam profiles obtained by classical spline functions. It has been shown that feature a single point of contact of cam into the follower has not been lost by fitting fourier series of obtained geometric model of cam profile even high valve lifts. Friction and inertia forces decreased due to the low speed and acceleration operation.
Bookmark/Search this post with
Abstract (Original Language): 
Bu çalışmada, homojen dolgulu sıkıştırma ile ateşlemeli (HCCI) bir benzin motoru için kam tasarımı ve imalatı yapılmıştır. 38 mm temel daire çapı ve 124° supap açık kalma süresi için, HCCI yanma karakteristiğine uygun 3,5, 5,5 ve 7,5 mm düşük supap kalkma miktarına sahip kamlar tasarlanmıştır. Dairesel yay eğrisi kullanılarak kam profillerinin genel geometrik modelleri elde edilmiş ve elde edilen kam profili modelleri fourier serisi ile ekstrapole edilerek daire yay eğrisine karşılık gelen eşitlikler türetilmiştir. Tasarlanan kam profilleri için iticinin hız, ivme ve sıçrama etkileri araştırılmıştır. Elde edilen sonuçlar 5. dereceden klasik spline yöntemi ile elde edilen kamlar ile mukayese edilmiştir. Klasik spline fonksiyonları ile elde edilen kam profillerinde supap kalkma miktarı arttıkça kamın iticiye tek noktadan temas özelliğinin kaybolduğu, iticilerin ivme ve sıçrama değerlerinin çok fazla arttığı görülmüştür. Geometrik modeli elde edilen kam profillerinin fourier serileri ile ekstrapole edilmesiyle, yüksek supap kalkma miktarlarında bile kamın iticiye tek noktadan temas etme özelliğinin kaybolmadığı, düşük hız ve ivme ile çalışması sonucu sürtünme ve atalet kuvvetlerinin azaldığı görülmüştür.
FULL TEXT (PDF): 
PDF icon arastirmax-homojen-dolgulu-sikistirma-ile-ateslemeli-bir-benzin-motoru-icin-kam-tasarimi-imalati.pdf
  • 1
15
22
  • Turkish

REFERENCES

References: 

1. Zhao, H., HCCI and CAI Engines for the
Automotive Industry, Woodhead Publishing
Limited, England, 2007.
2. Xingcai, L., Yuchun, H., Linlin, Z. ve Zhen H.,
“Experimental Study on the Auto-ignition and
Combustion Characteristics in the Homogeneous
Charge Compression Ignition HCCI Combustion
Operation with Ethanol/n-heptane Blend Fuels by
Port Injection”, Fuel, Cilt 85, 2622–2631, 2006.
3. Arcoumanis, C., Bae, C., Crookes R. ve
Kinoshita, E., “The Potential of Di-metyhlether
(DME) as an Alternative Fuel for Compression-
Ignition Engines”, A review, Fuel, Cilt 87, 1014-
1030, 2008.
4. Megaritis, A., Yap, D. ve Wyszynski, M.L.,
“Effect of Water Blending on Bioethanol HCCI
Combustion with Forced Induction and Residual
Gas Trapping”, Energy, Cilt 32, 2396-2400,
2007.
5. Yap, D., Karlovsky, J., Megaritis, A., Wyszynski,
M.L. ve Xu, H., “An Investigation into Propane
Homogeneous Charge Compression Ignition
(HCCI) Engine Operation with Residual Gas
Trapping”, Fuel, Cilt 84, 2372–2379, 2005.
6. Yoon, B.O., Dynamic Analysis and Optimal
Design of Over-Head Cam Systems, Ph.D.
Thesis, Mechanical Engineering, The University
of Michigan, Michigan, 1993.
7. Tsay, D.M. ve Huey, C.O., “Cam Motion
Synthesis Using Spline Functions”, Journal of
Mechanisms Transmissions and Automation
in Design, Cilt 110, 161-165, 1988.
C. Çınar ve A. Uyumaz Homojen Dolgulu Sıkıştırma ile Ateşlemeli Bir Benzin Motoru…
22 Gazi Üniv. Müh. Mim. Fak. Der. Cilt 29, No 1, 2014
8. Tsay, D.M. ve Huey, C.O., “Spline Functions
Applied to the Synthesis and Analysis of
Nonrigid Cam-Follower Systems”, Journal of
Mechanisms Transmissions and Automation
in Design, Cilt 111, 561-569, 1989.
9. Mandal, M. ve Naskar, T.K., “Introduction of
Control Points in Splines for Synthesis of
Optimized Cam Motion Program”, Mechanism
and Machine Theory, Cilt 44, 255-271, 2009.
10. Karabulut, H. ve Sarıdemir, S., “Farklı Supap
Açık Kalma Süreleri ve Kursları İçin Klasik
Spline Yöntemi İle Elde Edilen Kam Profillerinin
Karşılaştırılması”, Journal of the Faculty of
Engineering and Architecture of Gazi
University, Cilt 24, 509-515, 2009.
11. Lanni, C., Ceccarelli, M. ve Figliolini, G., “An
Analytical Design for Three Circular-Arc Cams”,
Mechanism and Machine Theory, Cilt 37, 915-
924, 2002.
12. Hsieh, J.F., “Design and Analysis of Cams with
Three Circular-Arc Profiles”, Mechanism and
Machine Theory, Cilt 45, 955-965, 2010.
13. Qiu, H., Lin, J.C., Li, Z.Y., Hiroaki, O., Wang, J.
ve Yong, Y., “A Universal Optimal Approach to
Cam Curve Design and Its Applications”,
Mechanism and Machine Theory, Cilt 40, 669-
692, 2005.
14. Mills, J.K., Notash, L. ve Fenton, R.G., “Optimal
Design and Sensitivity Analysis of Flexible cam
Mechanisms”, Mechanism and Machine
Theory, Cilt 28, 563-583, 1993.
15. Lampinen, J., “Cam Shape Optimisation by
Genetic Algorithm”, Computer Aided Design,
Cilt 35, 727-737, 2003.
16. Liang, Z. ve Quinn, C.J., “Accurate Design of a
Cam Profile on the CAD System”, Journal of
Manufacturing Systems, Cilt 10, 501-508,
1991.
17. Erlandsonn, O., “Thermodynamic Simulation
of HCCI Engine Systems”, Ph.D. Thesis, Lund
Institute of Technology, 2002.
18. He, B.Q., Xie, H., Zhang, Y., Qin, J. ve Zhao, H.,
“An Experimental Study on HCCI Combustion in
a Four Stroke Gasoline Engine with Reduced
Valve Lift Operations”, SAE Paper, 2005-01-
3736, 2006.
19. Jang, J. ve Bae, C., “Effects of Valve Events on
the Engine Efficiency in a Homogeneous Charge
Compression Ignition Engine Fueled by
Dimethyl Ether”, Fuel, Cilt 88, 1228–1234,
2009.
20. Zhang, Y., Zhao, H., He, B.Q. ve Xie, H.,
“Variable-Valve-Actuation-Enabled High-
Efficiency Gasoline Engine”, Journal of
Automobile Engineering, Cilt 224, 1081-1095,
2006.
21. Yeom, K., Jang, J. ve Bae, C., “Homogeneous
Charge Compression Ignition of LPG and
Gasoline Using Variable Valve Timing in an
Engine”, Fuel, Cilt 86, 494-503, 2007.
22. Grohe, H., Otto ve Dizel Motorları, Bilim
Teknik Yayınevi, İstanbul, 180-205, 19

Thank you for copying data from http://www.arastirmax.com