Determination of surface contact angle of a hybrid composite resin after different polishing
Journal Name:
- Süleyman Demirel Üniversitesi Sağlık Bilimleri Enstitüsü Dergisi
Keywords (Original Language):
Author Name | University of Author | Faculty of Author |
---|---|---|
Abstract (2. Language):
Objective: The aim of this study was to determine the effect of four different polishing applications on surface contact angle of composite samples after polimerizing with a halogen light unit. Method: A hybrid composite resin (Filtek-Z250) was used in the study. The composite resin samples (“10mm diameter x 2mm high”) were prepared in cylindirical teflon molds and samples were polymerized with a halogen light unit. Then they were ground with a 600 grid carborundum paper. Four different polishing procedures were applied on surfaces of samples; 1- Polishing discs set (Kerr-Hawe), 2- Light-polimerized polishing burnish (BisCover-LV), 3- Polishing pat/finishing discs/rubber (Enhance; Prisma Gloss), 4- Polishing pat/finishing discs/rubber (Enhance; Prisma Gloss Extra-Fine) (n=7). “Contact-Angle Measurement Device” (Easy Drop Gonyo-meter, Krüss,
Hamburg, Germany) was used to measure the contact angles of samples. The right and left contact angles of each drop were measured with “droplet method” and mean ranges were calculated.Two-way variance analyse and Dunnet-T3 multi-comparison test were used for statistical analyses (p<0,05). Results: Statistical differences were found on the effects of different polishing procedures (p<0,05). The lowest surface contact angle values were gained with polishing pat/finishing discs/rubber set (Enhance; Prisma Gloss), and the highest surface contact angle values were obtained with light-polimerized polishing burnish (BisCover-LV). Discussion: The lowest surface contact angle may be obtained by a polishing pat/finishing discs/rubber set.
Bookmark/Search this post with
Abstract (Original Language):
Amaç: Bu çalışmada, halojen ışık kaynağı ile polimerize edilen kompozit rezin örneklere dört farklı polisaj işlemi uygulanmasının, örneklerin yüzey temas açısı üzerine etkisinin belirlenmesi amaçlanmıştır.Yöntem: Çalışmada, hibrit bir kompozit rezin olan Filtek-Z250 kullanıldı. “10mm x 2mm” ebatlarındaki silindirik şekilli teflon kalıplarda hazırlanan kompozit örnekler halojen ışık kaynağıyla polimerize edildi ve 600 gridlik zımpara kağıdı ile zımparalandı. Örnek yüzeylerine; “1- Polisaj diskleri seti (Kerr-Hawe), 2- Işıkla-sertleşen rezin polisaj cilası (BisCover-LV), 3- Polisaj patı/bitirme diskleri/lastiği seti (Enhance; Prisma Gloss), 4- Polisaj patı/bitirme diskleri/lastiği seti (Enhance; Prisma Gloss Extra-Fine)” olmak üzere dört farklı polisaj seti ile polisaj işlemi uygulandı (n=7). Örneklerin yüzey temas açılarının ölçülmesinde “Temas-Açısı Ölçüm Cihazı” (Easy Drop Gonyo-meter, Krüss, Hamburg, Germany) kullanıldı. “Damlacık yöntemi” ile ve her damlacığın sağ ve sol temas açıları ölçülerek ortalama değerler hesaplandı. Veriler, İki-Yönlü Varyans-Analizi ve Dunnet-T3 Çoklu-Karşılaştırma-Testi‟yle istatistiksel olarak değerlendirildi (p<0,05). Sonuçlar: Farklı polisaj işlemlerinin, incelenen kompozit rezinin yüzey temas açısını istatistiksel olarak farklı etkilediği gözlendi (p<0,05). En düşük yüzey temas açısı değerleri sağlayan polisaj işlemi, polisaj patı/bitirme diskleri/lastiği seti (Enhance; Prisma Gloss) ile, en yüksek yüzey temas açısı değerleri gösteren polisaj işlemi ise polisaj cilasıyla (BisCover-LV) elde edildi (p<0,05). Tartışma: En düşük yüzey temas açısı bir polisaj patı/bitirme diskleri/lastiği seti ile elde edilebilir.
FULL TEXT (PDF):
- 2
62-68