Buradasınız

Anasayfa » Content

TAŞLAMADA PARAMETRELERİN ETKİSİ

THE EFFECT OF PARAMATERS IN THE GRINDING

Journal Name:

  • Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi

Publication Year:

  • 2001

Key Words:

Keywords (Original Language):

Author NameUniversity of AuthorFaculty of Author
Abstract (2. Language): 
The main purpose of grinding is to produce workpiece in required precision and surface finish. It is also used to machine workpiece above 50 Rc. Since the grinding is a finishing process or for a better passage to the following processes better combination of parameters in grinding must be achieved. In grinding process, because of the effect of the friction and subsequent plastic deformation residual stresses and metallurgic damages occurs in finished workpiece surfaces. Much work has been carried out to minimize these damages. In this article, the experimental and theoretical studies towards the improvement of grinding quality are reviewed.
Bookmark/Search this post with
Abstract (Original Language): 
Taşlamanın temel amacı; iş parçasının istenen yüzey kalitesi ve ölçü tamlığında üretilmesini sağlamak ve sertliği 50 Rc'den yüksek olan malzemeleri işlemektir. Taşlamanın bitirme işlemi olması veya daha sonraki işlemlere iyi bir geçiş sağlaması bakımından taşlama parametrelerinin iyi seçilip doğru belirlenmesi gerekmektedir. Taşlama işleminde sürtünme ve deformasyonun etkisiyle iş parçası yüzeyinde kalıcı gerilmeler meydana gelmekte ve metalurjik hasarlar oluşmaktadır. Bu hasarları azaltmaya ve taşlama kalitesini artırmaya yönelik bir takım çalışmalar yapılmaktadır. Bu makalede taşlama kalitesinin artırılmasına yönelik yapılmış olan teorik ve deneysel çalışmaların bir değerlendirilmesi yapılmıştır.
FULL TEXT (PDF): 
PDF icon arastirmax-taslamada-parametrelerin-etkisi.pdf
  • 2
189
198
  • Turkish

REFERENCES

References: 

Akkurt, M. 1996. Talaş Kaldırma Yöntemleri ve Takım Tezgahları, İ.T.Ü. Makina Fakültesi, İstanbul.
Anonim, 1977. TS 291. Taşlama Taşları, Türk Standardları, Ankara.
Benmalek, M.,
Gimenez
, P., Peyre, J. P. and Tournier, C. 1991. Characterisation And Comparison of Thin Layers Deposited by Different Physical Vapour Deposition Processes, Surface And Coatings Technology, (48), 181-187.
Brinksmeier, E., Cammett, J. J., Leskovar, P., Peters, J. And Tonshoff, H. K., Residual, 1982. Stresses-Measurement And Causes In Machining Processes. Ann. CIRP, (31), 491-510.
Bull, S. J. 1992. Correlation of Microstructure And Properties of Hard Coating, Vacuum, (43), 287-391.
Cander, P. 1975. "The Intrinsic Characteristics of Ground Surface", Reprinted From The Proceedings of The Abrasive Engineering Socity's International Technical Conference.
Chen, X., Brian, W. 1996a. Analysis and Simulation of The Grinding Process, Part II: Mechanics of Grinding, International Journal of Machine Tools&Manufacture, Pergaman, 36, 883-896.
Chen, X., Brian, W. 1996b. Analysis and Similation of The Grinding Process, Part III: Comparasion With Experiment, International Journal of Machine Tools&Manufacture, Pergaman, (36), 897-906.
Chen, X., Brian, W. 1999. A Grinding Power Model for Selection of Dressing And Grinding Conditions, Journal of Manufacturing Science And Engineering, ASME, (121), 632-637.
Demir, H. 1998. Alüminyum Oksit Zımpara Taşlarıyla Silindirik Taşlamada Çeşitli Çelikler İçin Taşlama Oranlarının Belirlenmesi, Yüksek Lisans Tezi, GÜ. Fen Bilimleri Enstitüsü, Makine Eğitimi.
Demir, H., Güllü, A. 1999. Silindirik Taşlamada Taşlama Parametrelerinin Yüzey Pürüzlülüğü Ve Taşlama Oranı Arasındaki İlişkinin Araştırılması, TEKNOLOJİ ZKÜ. Karabük Teknik Eğitim Fakültesi Dergisi, No (1-2), 159-167.
Fuh, K.,
Wabg
, S. 1997. Force Modelling and Forecasting In Creep Feed Grinding Using Improved BP Neural Network, International Journal of Machine Tools&Manufacture, Pergaman, 37,
1167-1178.
Mühendislik Bilimleri Dergisi 2001 7 (2) 189-198
196
Journal of Engineering Sciences 2001 7 (2) 189-198
Taşlamada Parametrelerin Etkisi, H. Demir, A. Güllü
Güllü, A. 1995. Silindirik Taşlamada İstenen Yüzey Pürüzlülüğünü Elde Etmek İçin Taşlama Parametrelerinin Bilgisayar Yadımı İle Optimizasyonu, Doktora Tezi, Gazi Üniversitesi Fen Bil. Ens. Makina Eğitimi, Ankara.
Güllü, A., Ercan, F., 1994. Zımpara Taşlarının Bilenmesi ve Taşlama Verimliliği, Endüstriyel Teknoloji Bilimsel ve Teknik Dergi, Ankara, 1 (1),
54-59.
Harris, M.W., Lavine, A.S. 1991. Thermal Aspects of Grinding:The Effect of The Wheel Bond on Heat Transfer To on Abrasive Grain, Journal of Engineering For Industry, (113), 395-401.
Henriksen, E. K. 1951. Residual Stresses in
Machined Surfaces, J. Appl. Mech., ASME, (73), 69-76.
Holmerg, K., Matthews, A. 1994. Coating Tribology, Elsevier, 11-268.
Jiang, L., Paro, J. 1996. Conparison of Hipped Austenitic 316L, Duplex 2205 And Super Duplex 2507 And As-Cast 304 Stainless Steels Using Alumina Wheel, Journal of Processing Technology,
Elsevier, (62), 1-9.
Kim., S.
H
, Ahn, J. H. 1999. Decision of Dressing Interval And Depth By The Direct Measurement Of The Grinding Wheel Surface, Journal of Processing
Technology, Elsevier, (88), 190-194.
Lemon, J., 1968. Study of Grinding Process As Applied To High-Strength Thermal-Resistant Alloys, Concart Af 33 (615)-5412, AFML-TR 68-309, Universty of Cincinati.
Lidsay R. P. 1971. On The Metal Removal And Wheel Removal Parameters, Suface Finish, Geometry And Thermal Damage In Precision Grinding, Ph.D. Dissertation, Worcester Polytechnic Institute.
Lim, G.H. 1995. Tool Wear in Machine Turning, Journal of Materials Processing Technology, 25-36.
Lissaman, A. J., Marti, S. J. 1982. Principles of Engineering Production, Second Edition, Great Britain.
Malikin, S. 1989. Grinding Technology and Applications, Ellis Horwood, Chichester.
Matsumoto, Y., Barash, M. And Liu, C. R. 1986. Effecting of Hardness on the Surface İntegrity of AISI 4340 Stell, J. Eng. Ind. ASME, (108), 196-175.
Matsuo, T., Sonoda, S., 1986. The Rating of Wheel in Laboratory Snag Grinding, Ann. CIRP, (29),
221.
Mcfarland, D. M., Bailey, G. E. 1999. The Desing and Analysis oof A Ploypropylene Hub CBN Wheel To Suppress Grinding Chatter, Journal of Manufacturing Science And Engineering, ASME, (121), 28-31.
Miller, M.H., Dow, T. A. 1999. Influence of The
Grinding Wheel In The Ductile Grinding of Brittle Material: Development And Verification of Kinematic Based Model, Journal of Manufacturing Science And Engineering, ASME, (121), 638-646.
Nakayama, K., Brecker, J., Shaw, M. C. 1971. Grinding Wheel Elastisity, Trans. ASME J. Engng
Ind. 93 (5), 609-614.
Pandey, S. J., Halder S. N., Lal, G. K. 1980.
Evaluation of Grinding Wheel Performance, Wear,
(58), 237.
Rajmohan, B., Radhakrishan, V. 1994. On The
Possibility of Process Monitoring in The Grinding By Spark Intensity Measurements, Jornal of Engineering For Indutry, (116), 124-129.
Ramseh, N., Radhakrishnan, V., Muriti, Y. V. S. 1980. Investigations on Laser Dressing Of Grinding Wheels, Part I. Preliminary Study, Journal of Engineering for Industry ASME, III, 244-251.
Robert, S. H., Lindsay, R. P. 1971. Principles of Grinding, Part I Basic Relationships in Precision Grinding, Reprinted From Machinery.
Ruisseax, N. R., Zerkle, R. D. 1970. Thermal Analysis of The Grinding Prcess, Journal of Engineering For Industry, 428-434.
Saini, D. P. 1990. Wheel Hardness and Local Elastic Deflections in Girinding, Int. Mach. Tools Manufact., (119), 509-519.
Saini, D. P., Wager, G. J., 1982. And Brown, R. H., Practical Significance of Contact Deflections İn Grinding, Ann, CIRP 31 (1), 215-219.
Schey, J. A. 1987. Introduction To Manufacturing Processes, Mc Graw Hill Book Company, Second Edition, Singapore, 441-553.
Shaw, M.C. 1994. A Production Engineering Approach To Grinding Temperatures, Journal of Materials Processing Technology, Elsevier, (44),
59-169.
Mühendislik
Bilimler
i Dergisi 2001 7 (2) 189-198
197
Journal of Engineering Sciences 2001 7 (2) 189-198
Taşlamada Parametrelerin Etkisi, H. Demir, A. Güllü
Srihari, G., Lal, G. K.
1994
. Mechanics of Vertical Surface Grinding, Journal of Processing Technology, Elsevier, Vol (44), 14-28.
Srihari, G., Lal, G. K. 1996. Mechanics of Vertical Surface Grinding, Journal of Processing Technology, Elsevier, 1 (62), 393-396.
Srivastava, A. K., Yuen K. M., and Ebestavi M. A. 1992. Surface Finish in Robotic Disk Grinding, International Journal of Machine Tools
and Manufacture, (32), 269-297.
Subramanian, K., Lindsay, R. P. 1992. A Systems Approcach for the Use of Vitrified Bonded Superabrasive Wheels for Precision Production Grinding, Journal of Engineering for Industry,_(114), 61-66.
Tetsuo. M. 1978. An Investigation of the Wear of Abrasive Grains, Kumamoto University, Japan.
Tonshoff, H. K., and Brinksmeier, E. 1980. Determination of Mehanical and Thermal Influences On Machined Surfaces By Microhardness and Residual Stresses Analysis. Ann. CIRP, (29), 519-530.
Verkerk, J. 1977. Final Report Concerning CIRP
Cooperative Work on The Characterization of Grinding Wheel Topography, Ann, CIRP 26 (2), 385-395.
Wen, M., Tay, A.O. and Nee, A. C. 1992. Micro¬Computer Based Optimization of The Surface Grinding Process, Journal of Materials Processing Technology, Elsevier, Vol (29), 75-90.
Yasui H. and Matsuo T. 1980. Characterization of Wheel Wear in High Depth of Cut Grinding, Department of Production Engineering, Kumamoto Uni., Japan .
Yu, X.X., Lau, W. S. 1999. A Finite-Element
Analysis of Residual Stress in Stretch Grinding, Journal of Processing Technology, Elsevier, (94),
13-22.
Yui, A. S., Lee, H. 1996. Surface Grinding With Ultra High Speed CBN Wheel, Journal of Materials Processing Technology, (62), 393-396.
Zhong P. S., Zhu, C. B. and Trmal G. 1994. An
Application of Expert System Approach To Production Grinding, Lapping and Polishing Processes For Optical Products, Journal of Processing Technology, Elsevier, (44), 179-186.

Thank you for copying data from http://www.arastirmax.com